FACULTAD DE CIENCIAS DE LA SALUD CARRERA PROFESIONAL DE ESTOMATOLOGÍA “RESISTENCIA A LA TRACCIÓN EN DENTINA CON SELLADO DENTINARIO INMEDIATO UNIDA A UNA RESINA BIS- ACRÍLICA: UN ESTUDIO IN VITRO” Tesis para optar el título profesional de: CIRUJANO DENTISTA Presentado por: Rodrigo Castro Ruiz (0000-0002-7744-4297) Asesor: Gino Hernán Vidalón Romo (0000-0002-3192-6784) Lima – Perú 2022 DEDICATORIA A mi familia en especial a mis padres, Martin Castro y Mariella Ruiz, a mi abuela Bertha Alvarez y a mi tio Fernando Ruiz, médico cardiólogo que en paz descansa. A mis hermanos Joaquin y Mariana Castro y a mi enamorada Stephany Sanguineti. AGRADECIMIENTOS Agradecimiento especial para mi asesor el doctor Gino Vidalón Romo, por haber aceptado y guiado con la mejor energía mi trabajo de investigación. ÍNDICE Pág. Título 1 Resumen 2 Abstract 3 I. Introducción 4 II. Metodología 6 III. Resultados 10 IV. Discusión 11 V. Conclusiones 14 VI. Referencias bibliográficas 15 VII. Anexos 17 ARTÍCULO ORIGINAL ENVIADO A PUBLICAR “RESISTENCIA A LA TRACCIÓN EN DENTINA CON SELLADO DENTINARIO INMEDIATO UNIDA A UNA RESINA BIS-ACRÍLICA: UN ESTUDIO IN VITRO” “TENSILE STRENGTH IN DENTIN WITH IMMEDIATE DENTIN SEALING BONDED TO A BIS- ACRYLIC RESIN: AN IN VITRO STUDY” Castro Ruiz R1, Vidalón Romo G1. 1. Carrera de Estomatología, Universidad Científica del Sur, Lima Perú. Correspondencia: Gino Hernán Vidalón Romo Dirección: UCSUR Campus Villa II, Carr. Panamericana Sur 19, Villa EL Salvador 15067 Correo: gvidalon@cientifica.edu.pe Conflictos de interés: Los autores declaran no tener algún conflicto de interés. Financiamiento: Autofinanciado RESUMEN Introducción: La co-polimerización de dobles enlaces residuales presente en la capa inhibida de oxígeno puede causar la adhesión química del material provisional en la superficie del sellado dentinario inmediato (SDI). Objetivo: Comparar la resistencia a la tracción en dentina con sellado dentinario inmediato unida a una resina bis-acrílica utilizando glicerina en gel y agua destilada en spray para el tratamiento de la capa inhibida de oxígeno. Metodología: 45 incisivos centrales y laterales inferiores bovinos con SDI unidos a la resina bis-acrílica Protemp (3M ESPE) distribuidos en 3 grupos según el tratamiento de la capa inhibida de oxígeno: (Control: Adhesivo Single Bond Universal (3M ESPE), Unidad LED Elipar Deep Cure-S (3M ESPE). G1: Glicerina (KY), Agua destilada (Matraz). G2: Agua destilada), seguido del test de tracción con la máquina de ensayos universales (CMT-5L; LG; 7419; Corea) a una velocidad de 1 mm/min respecto a la formula RU = F / A. Resultados: G1 mostró el promedio más alto de resistencia a la tracción (3,42 ± 0,302), seguido por Control (1,71 ± 0,152) y G2 (1,26 ± 0,131), el Post- Hoc de Tukey mostró diferencias significativas (p=0,0001) entre todos los grupos. Conclusiones: G2 presentó el promedio de resistencia a la tracción más bajo (1,26 ± 0,131), siendo la técnica más eficaz para reducir la resistencia a la tracción del material provisional al SDI. Palabras claves: Sellado dentinario inmediato, Capa inhibida de oxígeno, Resinas acrílicas, Restauración dental provisional, Adhesión, Resistencia a la tracción. ABSTRACT Introduction: The co-polymerization of residual double bonds present in the oxygen- inhibited layer can cause chemical adhesion of the provisional material on the surface of the immediate dentin sealant (IDS). Objective: To compare the tensile strength of dentin with immediate dentin sealing bonded to a bis-acrylic resin using glycerin gel and distilled water spray for the treatment of the oxygen-inhibited layer. Methodology: 45 bovine lower central and lateral incisors with SDI bonded to Protemp bis-acrylic resin (3M ESPE) distributed in 3 groups according to the treatment of the oxygen-inhibited layer: (Control: Universal Single Bond Adhesive (3M ESPE), Unit Elipar Deep Cure-S LED (3M ESPE). G1: Glycerin (KY), Distilled Water (Flask). G2: Distilled Water), followed by the tensile strength test with the universal testing machine (CMT-5L; LG; 7419; Korea) at a speed of 1 mm/min with respect to the formula RU = F / A. Results: G1 showed the highest average tensile strength (3.42 ± 0.302), followed by Control (1.71 ± 0.152). ) and G2 (1.26 ± 0.131), Tukey's Post-Hoc showed significant differences (p=0.0001) between all groups. Conclusions: G2 presented the lowest average tensile strength (1.26 ± 0.131), being the most effective technique to reduce the tensile strength of the provisional material to SDI. Keywords: Immediate dentin sealing, Oxygen-inhibited layer, Acrylic resins, Provisional restoration, Adhesion, Tensile strength.